Parts

Springs, Linear Bearings, etc.
Sort By:  
20T GT2 Aluminum Timing Pulley 3mm inner bore
R25.00
GT2 20 Tooth 5mm Bore
R20.00
GT2 Timing Belt 6mm wide 2mm Pitch 1M Length
R30.00
Use for linear actuators, CNC routers and 3D Printers.
R225.00
100K 1% NTC Single Ended Glass Sealed Thermistor Temperature Sensor For 3D Printer
R19.00
2 x High quality nickel plated springs.
R20.00
20T GT2 Aluminum Timing Idler Pulley (20T GT2 Aluminum Timing Idler Pulley)
Specifications:

Tooth: 20T
Model: With tooth
Material: Aluminum
Bore: 3mm
Width of gear: 7mm
20T GT2 Aluminum Timing Pulley 3mm inner bore
R25.00
608RS ABEC 9 Bearings (608RS-ABEC9)
Specification:
Material: Carbon steel
Inner Diameter: 8mm
Outer Diameter: 22mm
Thickness: 7mm

Plastic Seal
R7.50
GT2 20 Tooth Pulley (GT2 6mm Belt 5mm Bore Pulley)
GT2 Pulley:

Teeth: 20
Groove Width: Approx. 7mm
Total Width: Approx. 16mm
Diameter of Bore: Approx. 5mm
Flange: Double
Material: Aluminium
GT2 20 Tooth 5mm Bore
R20.00
GT2 Timing Belt 1M (GT2 6mm Belt)
Features:

1. Durable and practical
2. Designed specifically for linear motion

Specs:

GT2 Belt:
Pitch: GT2
Width: Approx. 6mm
Length: Approx. 1m (usually a few mm over)
GT2 Timing Belt 6mm wide 2mm Pitch 1M Length
R30.00
Nema 17 Stepper Motor 40mm 1.68A (SL42STH40-1684A)
Specification:
ModelSL42STH40-1684A
MaterialMetal
Dimension42x42x40mm
Step angle1.8°
Rated voltage2.8V
Rated current1.68A
Resistance/phase1.65Ω
Inductance/phase3.2mH
Moment of Intertia54g.cm2
Holding torque0.4Nm
Lead4
Orlentation torque150 g-cm

Features:
Application: Use for linear actuators, CNC routers and 3D Printers.
Low vibration and low noise
Low heat, smoother operation.
Better acceleration performance.
Round shaft.
 

Package Included:
1 x Nema 17 Stepper Motor
1 x 4 Wire cable with connector on motor end only

Use for linear actuators, CNC routers and 3D Printers.
R225.00
NTC 100K 3950 Thermistor (100K 3950 Thermistor)
Specs:
 
Thermistor with heat resistant wiring
100k Ohm NTC 3950
The thermistor leads are insulated with heat-resistant tubing, connections to the cables are heat-shrinked, and the ends of the wires are pre-stripped. Ready to install on your 3D printer or other DIY project with ease.
Glass encapsulated for long term stability & reliability
Small Size: φ1.25mm x 2.0mm glass orb
High Resistance Accuracy: 1%
Wide Temp. Range: −40°C to 270°C
Length: Approx. 1m
100K 1% NTC Single Ended Glass Sealed Thermistor Temperature Sensor For 3D Printer
R19.00
Springs (Springs)
Specifications:

Wire diameter: 1.2mm
Inner diameter: 5mm
Outer diameter 7.5mm
Height: 20mm
Material: stainless steel Nickel Plated.


Package included:

2 x Springs


2 x High quality nickel plated springs.
R20.00
Per Page      1 - 7 of 7
  • 1