Electronics

Sort By:  
Stepper motor driver with Full, 1/2, 1/4, 1/8 and 1/16 stepping modes.
R40.00
RepRap filtered endstop
R25.00
Integrated 3D Printer Controller Board produced by Makerbase
R450.00
A fully bundled board with 5 x TMC2208 V1.2 Stepper Drivers
R1,000.00
Stand alone full sized SD Card Slot
R45.00
Trinamic TMC2208 v1.0 Silent Stepper Drivers with pre-soldered headers.
R125.00
24V Power Supply 20A 480W (PSU 24V 480W)
Universal AC input full range
Output Voltage: 24V 20A
Power: 480W
Input Voltage: 110 / 220V
Size: 215 x 115 x 50mm
Shell Material: Metal case / Aluminum base.
Main Color:Silver Tone
Protection: Short Protection, Overload Protection, Over Voltage Protection.
Widely used in Industrial automation, LED display,communications, etc. IN-DOOR USE ONLY
Working Temperature: 0~40℃
Storage Temperature: -20~60℃
Ambient Humidity: 0~95% Non-Condensation
R499.00
A4988 Stepper Driver (A4988 Stepper Driver)
Description:

A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to the easy implementation. As long as the "step" input inputting one pulse drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened.

In the micro-step operation, A4988 chopping control inside automatically selects the current decay mode (Slow or Mixed). In mixed decay mode, the device is initially set to a fixed downtime in some fast decay, then the rest of the slow decay downtime. Mixed decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry is provided to improve the pulse-width modulation (PWM) operation power consumption. Internal circuit protection includes: thermal shutdown with hysteresis, undervoltage lockout (UVLO), and crossover-current protection. Special power sequencing.

A4988 surface mount QFN package (ES), a size of 5 mm × 5 mm, nominal overall package height of 0.90 mm, with an exposed pad for enhanced thermal dissipation. This package is Pb (suffix-T), with 100% matte tin leadframe plating.

Feature:

Simple step and direction control interface
Short-to-ground and shorted-load protection
Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates.

Package Includes:

1 x A4988
1 x Heatsync






Stepper motor driver with Full, 1/2, 1/4, 1/8 and 1/16 stepping modes.
R40.00
Endstop - RepRap Filtered (RepRap Endstop)
Features:

It using 22AWG wire, current up to 2A, 300V voltage. Insulated to cover a wide range of temperatures, and up to 80 degrees.
Board Size: Approx. 39 x 16 x 7mm / 1.54 x 0.63 x 0.28 inch
Cable Length: Approx. 70 cm / 27.56 inch

Connection Description:

Red: VCC (+)
Black: GND (-)
Yellow\Green: SIGNAL
RepRap filtered endstop
R25.00
FYSETC Duet 2 WiFi V1.04 (Duet 2 WiFi V1.04)

The Duet 2 WiFi is the 3D Printing board for enthusiasts. This board is produced by FYSETC in china using the open source plans released by the Duet designers.

Specs:

This is the latest PCB revision of the Duet 2 Wifi, v1.04.

Duet 2 Wifi is an advanced 32 bit electronics for the control of 3D printers and other CNC machines.

  • Dedicated Wifi module
  • Super quiet TMC2660 stepper drivers, up to 256 microstepping.
  • High speed SD card and support for a second SD external card if required.
  • Dual extruders on the main board, up to 5 more extruders on the expansion board.
  • High Power rating: Each stepper driver is capable of 2.8A motor current, currently limited in software to 2.4A. The bed heater channel is specifically designed for high current (18A).
  • Connect via PC, tablet or smartphone on the same network to the on board web interface.
  • Setup your printer and update the firmware through the web interface.
  • All common 3D printer geometries are supported
  • Expandable up to 7 extruders with Firmware support for mixing nozzles and remapping axes to use high power external drivers.
  • Support for the PanelDue: a full colour graphic touch screen
  • Provided with Molex compatible plugs and crimps.

The Duet 2 Wifi can have Thermistors connected directly to the board or optional daughterboards for other sensors can be ordered.


Included:

1 x Duet 2 Wifi V1.04 board.
5 x Heatsyncs
1 x USB Cable
Dupont Connectors and plugs.

R1,900.00
Geekcreit Wemos Mini D1 V3.0 (Wemos D1 Mini V3.0)
Optimized circuit board
Deep-Sleep jumper.
Default firmware: lastest MicroPython ESP8266 firmware.



Features:

11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0)
1 analog input(3.2V max input)
a Micro USB connection
Compatible with MicroPython, , Nodemcu

Package included:

1 x D1 mini V3.0.0
2 x Normal pin
2 x Long female pin
2 x Short female pin
R75.00
Makerbase MKS Gen L V1.0 (MKS Gen L V1.0)
Makerbase are a chinese company known for their quality mainboards and other printer hardware.

The MKS Gen L v1.0 is based on the RAMPS1.4 design with integrated Atmega2560-16AUR microcontroller, only the colour coding and pin layouts are far easier to work with and removes a lot of guess work that some people often encounter with the standard RAMPS setup. The redesign also makes it more compact than the standard RAMPS kit and just over all easier to work with. With support for both 12V and 24V it makes sure that it's a great upgrade for any printer.

Features:

1. 2560 and Ramps 1.4 are integrated in one board, which avoids the complicated connectors.

2. Support for a variety of stepper drivers such as A4988, DRV8825, TMC2100 and LV8729.

3. Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors.

4. Uses high-quality MOSFET, better cooling and more stable.

5. Uses a specific power chip, to support 12V-24V power input, and resolve the problems of chip heating and power shortage.

6. Stable and reliable filter circuit greatly reduces interference and avoids crashes.

7. Use CH340 serial port chip.

8. Runs Marlin firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4.

9. Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32.

10. Using 24v input can greatly reduce the time it takes to heat beds and hotends.

11. X axis, Y axis and Z axis are color coded terminals for the stepper motors and endstops, making it much easier to wire up.
Integrated 3D Printer Controller Board produced by Makerbase
R450.00
Makerbase MKS Gen L V1.2 with TMC2208 Stepper Drivers - Bundle (Gen L V1.0 Bundle)

Makerbase are a chinese company known for their quality mainboards and other printer hardware.

The MKS Gen L v1.0 is based on the RAMPS1.4 design with integrated Atmega2560-16AUR microcontroller, only the colour coding and pin layouts are far easier to work with and removes a lot of guess work that some people often encounter with the standard RAMPS setup. The redesign also makes it more compact than the standard RAMPS kit and just over all easier to work with. With support for both 12V and 24V it makes sure that it's a great upgrade for any printer.

Features:

1. 2560 and Ramps 1.4 are integrated in one board, which avoids the complicated connectors.

2. Support for a variety of stepper drivers such as A4988, DRV8825, TMC2100 and LV8729.

3. Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors.

4. Uses high-quality MOSFET, better cooling and more stable.

5. Uses a specific power chip, to support 12V-24V power input, and resolve the problems of chip heating and power shortage.

6. Stable and reliable filter circuit greatly reduces interference and avoids crashes.

7. Use CH340 serial port chip.

8. Runs Marlin firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4.

9. Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32.

10. Using 24v input can greatly reduce the time it takes to heat beds and hotends.

11. X axis, Y axis and Z axis are color coded terminals for the stepper motors and endstops, making it much easier to wire up.

Bundle includes:

1 x MKS Gen L V.1.0 Controller Board
5 x TMC2208 V1.2 Stepper Drivers
1 x SD Card Reader

A fully bundled board with 5 x TMC2208 V1.2 Stepper Drivers
R1,000.00
Mini 12864 RGB Display (Mini 12864 RGB Display)
  • 2.4" inch high contrast Graphic LCD
  • SPI communication to host micro-controller
  • Support Vertical or side SD slot with card detect,with a optional SD module
  • Rotary Encoder with RGB-Aura
  • Configurable RGB LED light
  • Software configurable contrast setting
  • 3D printable case and mount STL file
  • EXP1 & EXP2 RAMPS Compatible socket




Firmware config

This screen driver is ST7567 and is compatible with the marlin Mini panel (UC1701,same as ST7567). It has been tested, and the following configuration is required.

Before you start, please install the latest version of U8glib.

Step1. changes the pins.

On a RAMPS-compatible board, you need to make the following changes in pins_RAMPS.h:

pins_RAMPS.h 

#elif ENABLED(MINIPANEL) #define BEEPER_PIN 37 // Pins for DOGM SPI LCD Support #define DOGLCD_A0 16 #define DOGLCD_CS 17 #define LCD_BACKLIGHT_PIN -1 // backlight LED on A11/D65 #define LCD_RESET_PIN 23 #define SDSS 53 #define KILL_PIN -1 #define LCD_CONTRAST 200 #define BTN_EN1 31 #define BTN_EN2 33 #define BTN_ENC 35 //the click switch #define SD_DETECT_PIN 49
Step2. Config the configuration.h.

In order to control RGB-LED, you also need to turn on the RGB control in marlin.

You only need enable the NEOPIXEL_LED.

// Support for Adafruit Neopixel LED driver
/********** 1. only need enable the NEOPINEL_LED for mini12864 V2.1 **********/
#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
  #define NEOPIXEL_TYPE   NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
  #define NEOPIXEL_PIN    25        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
  #define NEOPIXEL_PIXELS 30       // Number of LEDs in the strip
  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
  #define NEOPIXEL_BRIGHTNESS 127  // Initial brightness (0-255)
  //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
#endif
Step3. Config the configuration_adv.h.

If you need to change the RGB-color manually, then you need to enable the LED_CONTROL_MENU in configuration_adv.h. If you don't need it, you can skip this step.

/**
 * LED Control Menu
 * Enable this feature to add LED Control to the LCD menu
 */
/********** 1. enable the LED_CONTROL_MENU RGB manual control **********/
#define LED_CONTROL_MENU
#if ENABLED(LED_CONTROL_MENU)
  #define LED_COLOR_PRESETS                 // Enable the Preset Color menu option
  #if ENABLED(LED_COLOR_PRESETS)
    #define LED_USER_PRESET_RED        255  // User defined RED value
    #define LED_USER_PRESET_GREEN      128  // User defined GREEN value
    #define LED_USER_PRESET_BLUE         0  // User defined BLUE value
    #define LED_USER_PRESET_WHITE      255  // User defined WHITE value
    #define LED_USER_PRESET_BRIGHTNESS 255  // User defined intensity
    //#define LED_USER_PRESET_STARTUP       // Have the printer display the user preset color on startup
  #endif
#endif // LED_CONTROL_MENU
Step4. add the codes in ultralcd_impl_DOGM.h.

You need to add a shorts codes to ultralcd_impl_DOGM.h, otherwise your screen may not have text displayed, or it may not be clear. Add "u8g.setContrast(255);" in the "static void lcd_implementation_init()" function:

1551170953232








R299.00
Nema17 Motor Cable 1M (Nema 17 Cable Black)

- Length: 1 Meter
Quantity: 1Pcs
Color: Black
HX2.54 4Pin to 6Pin Two-phase Four-lead
R35.00
SD Card Slot (Full Size SD Card Slot)
Great for upgrades where the SD Card slot was on the controller board or in situations where that the awesome case you printed doesn't cater for where the old one was.

Specifications:

- Size:45*40mm(L*W)
Model Number: V1.2 SD card module
Cable: 20cm Dupont cable
Suitable: for 3D Printer 
Stand alone full sized SD Card Slot
R45.00
Trinamic TMC2208 v1.2 Stepper Drivers (TMC2208 V1.2)
Features:
Hardware compatible with StepStick and Pololu A4988
Drive capability up to 1.2A (RMS) continuous coil current - 2A
Peak Step/Dir interface with microstep interpolation (up to 256 microsteps)
Configuration via CFG pins or UART interface
Motor supply voltage: 5.5...36V
Logic supply voltage: 3.3...5V
Components on the bottom for better heat dissipation
StealthChop2 - for quiet operation and smooth motion (default setting)
SpreadCycle - highly dynamic motor control chopper (enableable via UART)

Package includes:
1 x TMC2208






Trinamic TMC2208 v1.0 Silent Stepper Drivers with pre-soldered headers.
R125.00
Per Page      1 - 11 of 11
  • 1